14 best well pumps

Owners of private houses are well aware of the problem of water supply. Few localities in our country can boast the presence of a water supply network. Therefore, the water source becomes a well or a well. To raise the life-giving moisture to the surface of the earth, providing a home or a water irrigation system, requires a good borehole pump. When choosing this appliance, experts recommend paying attention to several parameters.

How to choose a pump for the well

1. Performance. It is not necessary to chase the high performance of the pump if the possibilities of the well or the well are unknown. The fact is that the filling of each water source is very different. It is very good when the well was made by professionals, after which they gave the owner a passport with the necessary data. Then the pump performance is chosen less than the filling of the well. But for the old wells will have to empirically determine the amount of water that comes in a unit of time. The capacity of downhole pumps ranges from 1 to 10 cubic meters. m / h Summer residents are able to fully provide water pump with a capacity of 1-3 cubic meters / h.
2. Head In order for water to flow from the tap with good pressure and not a thin stream, it is necessary to take into account such a parameter as the maximum pressure. It can be calculated as follows. 30 are added to the depth of the well (well), and 10% is also added to the resulting number. In the case of a 10-meter well, the optimum head will be 45 m.
3. Not all buyers pay attention to water quality when choosing a pump. If we are talking about supplying clean fluid from a well, then any model with the necessary set of characteristics will do. But in the case of water contaminated with sand, it is better to give preference to a screw pump that does not break down from the ingress of solid particles.
4. All pumps for wells are divided into two groups: submersible and surface. They have their pros and cons.
5. Submersible models able to supply water from great depths. Therefore, they are recommended to buy well owners with a depth of more than 10 m. In this category of pumps, vibration, screw and centrifugal units compete with each other. The most accessible of them are vibrational “streams” and “babies”. But with long-term use, well destruction occurs, and silting of wells occurs. Therefore, it is not necessary to spare money, the maintenance of a well or a well will later prove to be a more expensive project.
6. Surface models able to suck water only from shallow wells and boreholes (up to 10 m). They are good because they work indoors, they are easy to control and maintain.

In our review hit the 14 best pumps for wells. When compiling the rating, expert opinions and feedback from domestic users were taken into account.

Which well pump is better than screw or centrifugal?

Type of pump	Virtues	disadvantages
Screw	+ high head + no depth limits + not afraid of dirty water + simple maintenance + affordable price	- large overall dimensions - all pumps are submersible - there is no possibility to dispense the water supply
Centrifugal	+ versatility + compactness + high reliability + low noise + wide range	- requirements for water quality - high price

Rating of the best pumps for wells

Nomination	a place	Name of product	price
The best borehole pumps for dirty water	1	Sea-Land Verti Line 173 M	27 900 ₽
	2	Vodotok BTsE-GV-75-0,5-63m	14 700 ₽
	3	KAMA NPS-0.55-1.5 / 50	5 190 ₽
The best submersible borehole pumps for clean water	1	Aquatech SP 3.5 "4-100	25 869 ₽
	2	JELEX Water cannon PROF 55/90 House	19 700 ₽
	3	JELEX Water cannon PROF 55/75	7 950 ₽
The best surface borehole pumps for clean water	1	ESPA Aspri 35 4M N	34 125 ₽
	2	Pedrollo JSW 3AL-N	31 160 ₽
	3	Grundfos JP 6	16 950 ₽
	4	GARDENA 6000/6 inox Premium	14 073 ₽
	5	JELEX Jumbo 70/50 P	5 699 ₽
	6	Aquario ADB-60	5 333 ₽
	7	Vortex PN-650	3 510 ₽
	8	ESPA Aspri 15 3M	16 350 ₽

The best borehole pumps for dirty water

For pumping dirty water requires unpretentious pumps. Screw models handle this task best of all. In the field of view of the experts were the following electrical appliances.

Sea-Land Verti Line 173 M

Rating: 4.9

The Italian Sea-Land Verti Line 173 M borehole pump has the highest throughput capacity (6 cubic m / h). Thanks to a powerful motor (1990 W), the vertical single-block device is capable of solving serious problems. The pump is unpretentious enough to the quality of water, as long as it does not have fibrous or abrasive inclusions. The manufacturer used stainless steel, which makes the pump reliable and durable. Experts say a good combination of performance and low noise, for which the model deserves the first place in our rating. The motor has protection against overheating, sealing the joints made with rubber NBR.

Users have no complaints about the build quality, performance and durability of the device. The disadvantages include only the high price.

Vodotok BTsE-GV-75-0,5-63m

Rating: 4.7

The Chinese borehole pump Vodotok BTsE-GV-75-0,5-63m took the second place of our rating. He loses to the winner in power and performance, as used materials and assembly. But this model has a number of advantages that become decisive for domestic buyers. First of all, experts point out an affordable price. The device can be lowered to a depth of 120 m, and the maximum pressure reaches 110 m. It is worth mentioning the unpretentiousness of the pump. He is not afraid of sand and solid inclusions in water, thereby expanding the scope of its application.

Users use the Chinese pump to supply water from wells, ponds and wells, for organizing watering the garden. A long power cable (40 m) allows you to connect the device directly to a wall outlet.

KAMA NPS-0.55-1.5 / 50

Rating: 4.7

A good option for water supply may be to buy a Russian well pump KAMA NPS-0.55-1.5 / 50. The device has rather modest opportunities in comparison with the leaders of the rating. The capacity of the pump is 1.5 cu. m / h, the immersion depth is limited to 5 m, and the maximum pressure does not exceed 50 m. At the same time, experts note the economical power consumption (550 W) and silent operation. The model is unpretentious to the quality of water, the diameter of solid particles can reach 1 mm. The manufacturer completed the product with a long power cord (15 m).

Many users had time to evaluate the quality of the domestic pump. It copes with the water supply of a small house and with watering the beds.Thanks to the use of corrosion-resistant materials, the pump can serve for a long time without breakage.

The best submersible borehole pumps for clean water

All submersible pumps can pump clean water. When buying, it is important to determine only the technical characteristics of the model. A high rating from specialists received several devices.

Aquatech SP 3.5 "4-100

Rating: 4.9

A pronounced leader among borehole pumps in all major indicators is the Aquatech SP 3.5 "4-100 model. The Chinese device has a high throughput (4.8 cubic meters / h), which is provided by an electric motor with a capacity (1.5 kW). The pump is designed for pumping clean water, it can work both in continuous mode and with frequent on / off.The pump’s immersion depth reaches 80 m, and the pumping pressure is 100 m. The long power cord (70 m) allows you to connect the device without lengthening teley.

The owners of the Chinese pump are pleased with its performance, build quality, silent operation. The only disadvantage of the model against the background of competitors is the high price.

JELEX Water cannon PROF 55/90 House

Rating: 4.8

A little behind the leader of the rating in terms of key parameters is the Russian well pump GILEKS Vodomet PROF 55/90 Dom. The flow capacity (3.3 cubic meters / h), engine power (1.1 kW), immersion depth (30 m) and maximum head (90 m) look somewhat more modest. However, the model looks more profitable in terms of equipment. First of all, the device is supplied with a 50 l hydroaccumulator. Self-sufficient system does not require special attention from the owner. It has protection against overload and dry running. The presence of a control panel allows programming remotely.

In reviews, users praise the pump for complete packaging, informative display, reliability. Among the shortcomings, there is a weak corrosion protection of the hydroaccumulator.

JELEX Water cannon PROF 55/75

Rating: 4.7

For pumping water from wells and boreholes, a well pump is designed. It has an affordable price, its technical characteristics do not reach the parameters of the rating leaders. Since the maximum pressure is limited to 75 m, the immersion depth should not exceed 30 m. At the same time, the device economically consumes electricity (880 W). The model is quite unpretentious to the quality of the water, inside there is a strainer that retains particles larger than 1.5 mm in size. The length of the power cord is 30 m.

Owners in the reviews praise the pump for its quiet operation, low price, a clear response protection against overheating. Of the disadvantages of poor equipment noted, there are problems during operation.

The best surface borehole pumps for clean water

Compact size and ease of operation attract users of surface pumps. They allow you to extract water from wells with a depth of 7-10 m. It is better to install such pumps in separate rooms, since they make a decent noise. The experts liked the following surface installations.

ESPA Aspri 35 4M N

Rating: 4.9

High quality and a wonderful set of technical parameters allowed the Spanish pump ESPA Aspri 35 4M N to take the first place in our rating. The manufacturer made all the important parts of stainless steel, which had a positive effect on the reliability and durability of the device.The design provides an oil-filled chamber, which is responsible for lubricating the shaft seal. Experts highly appreciated the presence of a self-priming valve in the pump, which provides a suction height of 9 m. The pump has thermal protection of a single-phase motor, as well as an automatic restart. The capacity of the surface pump is 9 cu. m / h

Users are flattering about the power, reliability and silent operation of the pump. The downside of the model is the high price.

Pedrollo JSW 3AL-N

Rating: 4.8

The high-quality surface pump Pedrollo JSW 3AL-N takes the second place in the rating. The model demonstrates the best technical parameters. These are high throughput (9.6 cubic meters / h), high head (62 m), considerable immersion depth (9 m). Unlike the winner, some parts are made of cast iron, for example, the case. It should be noted that metal surfaces are reliably protected with high-quality paint and varnish coating. The model loses a bit to the leader in weight (27 kg) and overall dimensions. The device is easy to install and maintain.

Domestic users have no particular complaints about the work of the Italian pump. It is distinguished by its efficiency and versatility, allowing with equal success to organize the water supply to the house and water the garden.

Grundfos JP 6

Rating: 4.7

For its lightness (12 kg), compactness and stylish appearance, the surface pump Grundfos JP 6 has won praise from the experts. But not only these qualities allowed the model to get into the top three rankings. The Hungarian pump is characterized by quiet operation, easily lifting water from a depth of 8 m. Self-priming is provided by an external ejector. In this case, the pump does not have a record capacity (5 cubic m / h) and power (1.4 kW). The device is optimally suitable for water supply of summer cottages and organization of the irrigation system.

Users are satisfied with quiet operation, normal pressure, reliability. It is quite simple to connect it, without even looking at the enclosed instructions. Of the minuses there is a lack of automatic pressure and a short power cord.

GARDENA 6000/6 inox Premium

Rating: 4.7

The surface pump GARDENA 6000/6 inox Premium is a premium class product. The Czech model is sold at a reasonable price thanks to the Chinese assembly. Experts drew attention to the innovative engine protection mechanism, which ensures the durability of the electric device. The bright LED indicator allows you to follow the workflow, it signals in a timely manner about problems. The use of stainless steel in the manufacture of the body increases the reliability of the pump. The model is unpretentious to the quality of water, it pumps plumbing, rainwater and chlorinated water.

In reviews, the pump is praised for its compactness, automaticity and noiselessness. To get on the pedestal of our rating of the product does not allow non-reproducibility.

JELEX Jumbo 70/50 P

Rating: 4.6

Good reviews are addressed in the thematic forums of the Russian surface pump JELEX Jumbo 70/50 P. Let this model not have high performance indicators (3.9 cubic meters / h) and power (1.1 kW). But it creates a maximum pressure of 45 m, and the depth of absorption reaches 9 m. Unlike the leaders of the rating, the pump has a plastic case. On the one hand, he is not afraid of corrosion, but the owner must carefully handle the device. A decent self-priming depth is provided by the standard ejector.

Users note the reliability, reliability, affordability and unpretentiousness of the domestic pump. Thanks to protection against overheating, timely shutdown of the engine occurs. The obvious disadvantages include a high noise level during operation.

Aquario ADB-60

Rating: 4.5

If the suction depth does not exceed 7 m, then you should pay attention to the surface pump Aquario ADB-60. The budget model from Italy stands out favorably from competitors by high pressure (64 m). At the same time, the pump is inferior in such indicators as throughput (2.4 cubic m / h) and power (600 W). The manufacturer has equipped its product with pressure boosting and overheating protection. The pump casing is made of cast iron, which is protected from corrosion by electroplating.

The Italian pump is well established in our country. Users are satisfied with its reliability, pressure, low price. Even in the absence of water, there were no cases of failure. Only modest performance and unsightly appearance did not allow to rise higher in the rating.

Vortex PN-650

Rating: 4.4

Domestic development WHIRL MON-650 is addressed to owners of private houses. The manufacturer offers the lowest price for a surface pump. The emphasis is on good throughput (3.6 cubic m / h), maximum head (45 m) and light weight (8 kg). The model is assembled from sturdy parts, the case is cast from cast iron, protected from moisture paint coating. Pleasantly surprised by the experts and a large suction depth (9 m). It is difficult to expect a rich functional content from the budget model, so the model is located on the seventh line of the rating.

The strengths of the Whirlwind owners include compactness, lightness, low price and suction depth. The lack of automation is a disadvantage of the unit, as indicated in the reviews.

ESPA Aspri 15 3M

Rating: 4.4

The ESPA Aspri 15 3M surface pump boasts a wide range of applications. It is able to raise water from wells and ponds, work in modular water supply and irrigation systems, pump water from one tank to another. Unlike the relative who won in our rating, the model has modest possibilities. It has a minimum head (33 m), a modest power (610 W) and a throughput (3 cubic m / h). The strengths of the product experts include the depth of absorption (9 m) and low weight (9.2 kg).

The pump closes our rating because of the high price. Some users had difficulty controlling the pump. But for quiet operation, smooth start and the absence of vibration, the device deserves praise.

---

Attention! This rating is subjective, is not advertising and does not serve as a guide to the purchase. Before buying, you should consult with a specialist.